BenQ SH915 Manual do Utilizador

SH915/SW916Digital ProjectorUser Manual

Introduction10Projector exterior view1. Lamp compartment cover2. Quick-release button3. Projection lens4. Focus ring and Zoom ring5. External control

Introduction 1130. Ceiling mount holes31. Rear adjuster footBottom side30313030

Introduction12Controls and functionsProjectorSH915SW9161. FOCUS/ZOOM RingUsed to adjust the projected image appearance. See "Fine-tuning the imag

Introduction 1310. ► Right/ Increase volume levelIncreases volume. See "Adjusting the sound level" on page 47 for details. (available in SH9

Introduction14Remote ControlSH9151. ON / OFFToggles the projector between standby mode and on.2. Source selection buttonsSelects an input source fo

Introduction 1520. MUTEToggles projector audio between on and off.21. SMART ECOSwitch the lamp mode between Eco/Normal and SmartEco.22. QUICK INSTALL

Introduction16SW9161. ON / OFFToggles the projector between standby mode and on.2. Source selection buttonsSelects an input source for display.3. K

Introduction 1719. MUTEToggles projector audio between on and off.20. LAMP MODEDisplays the Lamp Mode OSD menu.Operating the LASER pointerThe Laser Po

Introduction18Remote control effective rangeInfra-Red (IR) remote control sensor is located on the front and the rear of the projector. The remote con

Introduction 19Replacing the remote control battery1. To open the battery cover, turn the remote control over to view its back, push on the finger gri

Table of contents2Ta b l e o f c o n t e n t sImportant safety instructions ... 3Introduction... 7Projector features.

Positioning your projector20Positioning your projectorChoosing a locationYour projector is designed to be installed in one of four possible installati

Positioning your projector 21Obtaining a preferred projected image sizeThe distance from the projector lens to the screen, the zoom setting (if availa

Positioning your projector22SW916The screen aspect ratio is 16:10 and the projected picture is 16:10.There is 5% tolerance among these numbers due to

Connection 23ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the

Connection24Connecting video source devicesYou need only connect the projector to a video source device using just one of the connecting methods, howe

Connection 25Playing sound through the projectorYou can make use of the projector (mixed mono) speaker in your presentations, and also connect separat

Operation26OperationStarting up the projector1. Remove the lens cap.2. Plug the power cord into the projector and into a wall socket. Turn on the wall

Operation 27Adjusting the projected imageAdjusting the projection angleThe projector is equipped with 1 quick-release adjuster foot and 1 rear adjuste

Operation28Fine-tuning the image size and clarityCorrecting keystoneKeystoning refers to the situation where the projected image is noticeably wider a

Operation 29Correcting 2D Keystone2D Keystone function enables a wider projector installation area compared to conventional projectors with limited po

Important safety instructions 3Important safety instructionsYour projector is designed and tested to meet the latest standards for safety of informati

Operation30Correcting Corner FitManually adjust four corners of the image by setting the horizontal and vertical values.•Using the OSD menu1. Press ME

Operation 31Correcting Surface FitManually correct geographic distortion by Surface Fit calibration function.•Using the OSD menu1. Press MENU/EXIT and

Operation328. Press ◄/► to select the direction and press MODE/ENTER.9. Press ▲/▼ to adjust the top or/and bottom side convex or concave. Default is 0

Operation 33Using the menusThe projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.Below is the overv

Operation34Securing the projectorUsing a security cable lockThe projector has to be installed in a safe place to prevent theft. Otherwise, purchase a

Operation 35If you forget the passwordIf the password function is activated, you will be asked to enter the six-digit password every time you turn on

Operation366. You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.7.

Operation 37Switching input signalThe projector can be connected to multiple devices at the same time. However, it can only display one full screen at

Operation38Magnifying and searching for detailsIf you need to find the details on the projected picture, magnify the picture. Use the direction arrow

Operation 39About the aspect ratioIn the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can

Important safety instructions4Safety Instructions (Continued)7. The lamp becomes extremely hot during operation. Allow the projector to cool for appro

Operation40Optimizing the imageUsing Wall ColorIn the situation where you are projecting onto a colored surface such as a painted wall which may not b

Operation 416. Press ▼ to select a sub-menu item to be changed and adjust the value with ◄/►. See "Fine-tuning the image quality in user modes&qu

Operation42Setting a preferred color temperatureTo set a preferred color temperature:1. Highlight Color Temperature and select Warm, Normal or Cool by

Operation 43Please refer to the illustration to the right for how the colors relate to each other.For example, if you select Red and set its range at

Operation443. Press ▼ to highlight Timer Display and choose if you want the timer to show up on the screen by pressing ◄/►.4. Press ▼ to highlight Tim

Operation 45Freezing the imagePress FREEZE on the remote control to freeze the image. The word 'FREEZE' will appear on the screen. To releas

Operation46Operating in a high altitude environmentWe recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above s

Operation 47Adjusting the sound levelTo adjust the sound level,• Using the remote controlPress or to select a desired sound level.•Using the OSD m

Operation48Using the teaching templatesThe projector provides several preset patterns for various teaching purposes. To activate the pattern:1. Open t

Operation 49Controlling the projector through a LAN environmentNetwork Settings allow you to manage the projector from a computer using a web browser

Important safety instructions 5Safety Instructions (Continued)13. Do not place this projector in any of the following environments.- Space that is poo

Operation50Configuring the Wireless LAN Settings1. Connect the BenQ wireless dongle (optional) to the USB TYPE-A input jack of the projector.2. Select

Operation 512. The BenQ remote network operation page opens.• The web page control supports IE version 7.0 or higher.• The illustrations in web page c

Operation52i. These buttons function the same as the ones on the remote control. See "Remote Control" on page 14 for details.The Display Set

Operation 53The Information page displays the information and status of this projector.The Conference Control page allows you to control computer’s di

Operation54The Crestron page is only available when you are on a Wired LAN network. It also allows you to control the projector remotely. The Crestron

Operation 55i. You can name the projector, keep track of its location and the person in charge of it.ii. You can adjust the Wired LAN settings.iii. On

Operation56The Basic page allows you to change the password and select connected persons. The number of connected persons may affect the network displ

Operation 57The Wireless LAN page allows you to adjust the Wirless LAN settings.Max. length for SSID string is 16 bytes. Please use a different SSID w

Operation58Using the Web Control LockThis function is designed to prevent unauthorized people from maliciously changing the projector settings through

Operation 595. Click the Search icon.The Search page allows you to search and connect a network display.i. You can key in the IP address (see "Co

Important safety instructions6Safety Instructions (Continued)17. Do not step on the projector or place any objects upon it. Besides probable physical

Operation60i. Full Screen: whole image display on the projector. Selectable: a square will popup then you can move and drag the area you want to show

Operation 61iii. When you install the Q Presenter, the program will automatically identify the language of your computer’s operating system and instal

Operation62Using the broadcassting functionWhen it comes to 1:N LAN Dispaly,there are two ways to do this function:1. By TCP/IP (support up to 8 porje

Operation 63Remote Desktop Control through Q PresenterThe Q Presenter can proceed the Remote Desktop Control (RDC) the host PC from projector site.1.

Operation644. Select Remote Desktop and press MODE/ENTER.5. Enter the Account and Password the same as step 1.6. Select Connect and press MODE/ENTER t

Operation 65USB Reader menuThe USB Reader menu will display only when USB Reader source is selected. This menu is includes with a slideshow feature fo

Operation66Menu operationMenu systemPlease note that the on-screen display (OSD) menus vary according to the signal type selected.Main menu Sub-menu O

Operation 672. PicturePicture ModeDynamic/Presentation/sRGB/Cinema/3D/User 1/User 2Reference ModeDynamic/Presentation/sRGB/Cinema/3DBrightnessContrast

Operation684. System Setup: BasicPresentation TimerTimer Period 1~240 minTimer Display Always/1 min/2mins/3 mins/NeverTimer PositionTop-Left/Bottom-Le

Operation 695. System Setup: AdvancedHigh Altitude ModeOn/OffAudio SettingsMute On/OffVolum ePower on/off Ring YES/NOLamp SettingsLamp Mode Normal/Eco

Introduction 7IntroductionProjector featuresThe projector offers the following features• SmartEco™ starts your dynamic power savingThe SmartEco™ techn

Operation70Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the proj

Operation 71Description of each menuFUNCTION DESCRIPTION 1. Display menuWall colorCorrects the projected picture’s color when the projection surface i

Operation721. Display menu3DThis projector features a 3D function which enables you to enjoy the 3D movies, videos, and sporting events in a more real

Operation 732. Picture menuPicture ModePre-defined picture modes are provided so you can optimize your projector image set-up to suit your program typ

Operation744. System Setup: Basic menuPresentation TimerReminds the presenter to finish the presentation within a certain time frame. See "Settin

Operation 754. System Setup: Basic menuOperation SettingDirect Power OnPowers projector on automatically when the power cable is connected.Signal Powe

Operation765. System Setup: Advanced menuHigh Altitude ModeA mode for operation in high altitude areas. See "Operating in a high altitude environ

Operation 775. System Setup: Advanced menuStandby SettingsNetworkSelecting On enables the function. The projector is able to provide the network funct

Operation78The Information menu shows you the current operating status of the projector.6. Information menuCurrent System StatusSourceShows the curren

Maintenance 79MaintenanceCare of the projectorYour projector needs little maintenance. The only thing you need to do on a regular basis is to keep the

Introduction8• The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/b

Maintenance80Lamp informationGetting to know the lamp hourWhen the projector is in operation, the duration (in hours) of lamp usage is automatically c

Maintenance 81Timing of replacing the lampWhen the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please

Maintenance82Replacing the lamp• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one

Maintenance 8310. Restart the projector.Do not turn the power on with the lamp cover removed.5. Lift the handle so that it stands up. Use the handle t

Maintenance84Resetting the lamp timer11. After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Set

Maintenance 85IndicatorsLight Status & DescriptionPower Te m p LampPower eventsOrange Off Off Stand-by modeGreenFlashingOff Off Powering upGreen O

Troubleshooting86TroubleshootingThe projector does not turn on.No pictureBlurred imageRemote control does not workThe password is incorrectCause Remed

Specifications 87SpecificationsProjector specifications All specifications are subject to change without notice.OpticalResolutionSH9151920 x 1080SW916

Specifications88Dimensions360.1 mm (W) x 119.9 mm (H) x 259 mm (D)259119.9360.152.3Ceiling Mount Installation *Ceiling Mount Screws: M4 (Max. L=25, M

Specifications 89Timing chartSupported timing for PC inputResolution Format Refresh rate (Hz)H- frequency (kHz)Pixel Frequency (MHz)720 x 400 720 x 40

Introduction 9Shipping contentsCarefully unpack and verify that you have all of the items shown below. If any of these items are missing, please conta

Specifications90* Supported timing for 3D signal with Frame Sequential, Top-Bottom and Side-by-Side format.** Supported timing for 3D signal with Fram

Specifications 91Support timing for Video input* Supported timing for 3D signal with Frame Sequential format.Support timing for HDMI (HDCP) inputForma

Specifications92* Supported timing for 3D signal with Frame Sequential, Top-Bottom and Side-by-Side format.** Supported timing for 3D signal with Fram

Specifications 93Supporting timing for HDMI Video input* Supported timing for 3D signal with Frame Sequential, Frame Packing, Top-Bottom and Side-by-S

Warranty and Copyright information94Warranty and Copyright informationLimited warrantyBenQ warrants this product against any defects in material and w