BenQ MW727 Manual do Utilizador

MX726/MW727Digital ProjectorUser Manual

Introduction10Projector exterior view1. Lamp compartment cover2. External control panel (See "Projector" on page 12 for details.)3. Focus ri

Introduction 1128. Front adjuster foot29. Ceiling mount holes30. Rear adjuster footBottom side2930292928

Introduction12Controls and functionsProjector 1. FOCUS/ZOOM RingUsed to adjust the projected image appearance. See "Fine-tuning the image size an

Introduction 13Remote Control 1. ON / OFFToggles the projector between standby mode and on.2. Source selection buttonsSelects an input source for d

Introduction14When the projector is under MHL mode, The keypad on projector should be with the same definition of the key on remote control.Controllin

Introduction 15(Available in Japan region)1. ON / OFFToggles the projector between standby mode and on.2. Source selection buttonsSelects an input

Introduction1618. MIC/VOL +/MIC/VOL -Microphone input level adjustment.19. MUTEToggles projector audio between on and off.20. SMART ECOSwitch the lamp

Introduction 17Remote control effective range Infra-Red (IR) remote control sensor is located on the front and the rear of the projector. The remote c

Introduction18Replacing the remote control battery1. To open the battery cover, turn the remote control over to view its back, push on the finger grip

Positioning your projector 19Positioning your projectorChoosing a locationYour projector is designed to be installed in one of four possible installat

Table of contents2Ta b l e o f c o n t e n t sImportant safety instructions ... 3Introduction... 7Projector features.

Positioning your projector20Obtaining a preferred projected image sizeThe distance from the projector lens to the screen, the zoom setting (if availab

Positioning your projector 21MW727The screen aspect ratio is 16:10 and the projected picture is 16:10. There is 5% tolerance among these numbers due t

Connection22ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the

Connection 23FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

Connection24Playing sound through the projectorYou can make use of the projector (mixed mono) speaker in your presentations, and also connect separate

Operation 25OperationStarting up the projector1. Remove the lens cap.2. Plug the power cord into the projector and into a wall socket. Turn on the wal

Operation26Adjusting the projected imageAdjusting the projection angleThe projector is equipped with 1 front adjuster foot and 1 rear adjuster foot. T

Operation 27Correcting 2D Keystone2D Keystone function enables a wider projector installation area compared to conventional projectors with limited po

Operation28Correcting Corner FitManually adjust four corners of the image by setting the horizontal and vertical values.•Using the OSD menu1. Press ME

Operation 29Using the menusThe projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.Below is the overv

Important safety instructions 3Important safety instructionsYour projector is designed and tested to meet the latest standards for safety of informati

Operation30Securing the projectorUsing a security cable lockThe projector has to be installed in a safe place to prevent theft. Otherwise, purchase a

Operation 31If you forget the passwordIf the password function is activated, you will be asked to enter the six-digit password every time you turn on

Operation32Changing the password1. Open the OSD menu and go to the System Setup: Advanced > Security Settings > Change password menu.2. Press MO

Operation 33Switching input signalThe projector can be connected to multiple devices at the same time. However, it can only display one full screen at

Operation34Magnifying and searching for detailsIf you need to find the details on the projected picture, magnify the picture. Use the direction arrow

Operation 35About the aspect ratioIn the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can

Operation36Optimizing the imageUsing Wall ColorIn the situation where you are projecting onto a colored surface such as a painted wall which may not b

Operation 37Setting the User 1/User 2 modeThere are two user-definable modes if the current available picture modes are not suitable for your need. Yo

Operation38Selecting a Color TemperatureThe options available for color temperature* settings vary according to the signal type selected.1. Cooler: ma

Operation 392. Press MODE/ENTER and the 3D Color Management page displays.3. Highlight Primary color and press ◄/► to select a color from among Red, G

Important safety instructions4Safety Instructions6. Do not block the projection lens with any objects when the projector is under operation as this co

Operation40Setting the presentation timerPresentation timer can indicate the presentation time on the screen to help you achieve better time managemen

Operation 41Remote paging operationsConnect the projector to your PC or notebook with a USB cable prior to using the paging function. See "Connec

Operation42Locking control keysWith the control keys on the projector locked, you can prevent your projector settings from being changed accidentally

Operation 43Muting the soundTo temporarily turn off the sound,• Using the remote controlPress MUTE to temporarily turn off the sound. While the sound

Operation44Using the teaching templatesThe projector provides several preset patterns for various teaching purposes. To activate the pattern:1. Open t

Operation 45Shutting down the projector1. Press POWER or OFF and a confirmation message will appear prompting you.If you don't respond in a f

Operation46Menu operationMenu systemPlease note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu Sub-menu

Operation 472. PicturePicture ModeDynamic/Presentation/sRGB/Cinema/3D/User 1/User 2Reference ModeDynamic/Presentation/sRGB/Cinema/3DBrightnessContrast

Operation484. System Setup: BasicPresentation TimerTimer Period 1~240 minTimer Display Always/1 min/2mins/3 mins/NeverTimer PositionTop-Left/Bottom-Le

Operation 495. System Setup: AdvancedHigh Altitude ModeOn/OffAudio Settings Mute On/OffVolumeMicrophone VolumePower on/off Ring On/OffLamp SettingsLam

Important safety instructions 5Safety Instructions (Continued)12. When the projector is under operation, you may sense some heated air and odor from i

Operation50Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the proj

Operation 51Description of each menuFUNCTION DESCRIPTION 1. Display menuWall colorCorrects the projected picture’s color when the projection surface i

Operation521. Display menu3DThis projector features a 3D function which enables you to enjoy the 3D movies, videos, and sporting events in a more real

Operation 532. Picture menuPicture ModePre-defined picture modes are provided so you can optimize your projector image set-up to suit your program typ

Operation544. System Setup: Basic menuPresentation TimerReminds the presenter to finish the presentation within a certain time frame. See "Settin

Operation 554. System Setup: Basic menuRemote ReceiverSets the preferred remote receiver (Front and Rear) allowing the projector to accept signals fro

Operation565. System Setup: Advanced menuSecurity SettingChange passwordYou will be asked to enter the current password before changing to a new one.

Operation 575. System Setup: Advanced menuStandby SettingsNetwork• Enable Network Standby Mode Selecting On enables the function. The projector is abl

Operation58The Information menu shows you the current operating status of the projector.5. System Setup: Advanced menuNetwork settingsWired LANSee Ben

Maintenance 59MaintenanceCare of the projectorYour projector needs little maintenance. The only thing you need to do on a regular basis is to keep the

Important safety instructions6Safety Instructions (Continued)16. Do not stand the projector on end vertically. Doing so may cause the projector to fal

Maintenance60Lamp informationGetting to know the lamp hourWhen the projector is in operation, the duration (in hours) of lamp usage is automatically c

Maintenance 61Timing of replacing the lampWhen the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please

Maintenance62Replacing the lamp• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one

Maintenance 635. Loosen the two captive screws that secure the lamp.• Do not turn the power on with the lamp cover removed.• Do not insert your finger

Maintenance6412. Restart the projector.Do not turn the power on with the lamp cover removed.Resetting the lamp timer13. After the startup logo, open t

Maintenance 65Indicators Light Status & DescriptionPower Te m p LampPower eventsOrange Off Off Stand-by modeGreenFlashingOff OffPowering upGreen O

Maintenance66System eventsGreen Off RedThe projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please

Troubleshooting 67TroubleshootingThe projector does not turn on. No picture. Blurred image. Remote control does not work. The password is incorrect. C

Specifications68SpecificationsProjector specificationsAll specifications are subject to change without notice. OpticalResolutionMX7261024 x 768MW72712

Specifications 69Dimensions314.2 mm (W) x 116 mm (H) x 216.3 mm (D)314.2216.3314.251.2116.065.245.676.0 109.071.090.5537.9577.7636.981.8314.2216.3Ceil

Introduction 7IntroductionProjector featuresThe projector offers the following features• SmartEco™ starts your dynamic power savingThe SmartEco™ techn

Specifications70Timing chartSupported timing for PC input Resolution ModeRefreshrate(Hz)H-frequency(kHz)Clock(MHz)3D FieldSequential3Dover-under3Dside

Specifications 71There 3D timing showing depend the EDID file and VGA display card. It is possible that user cannot choose the above 3D timings on VGA

Specifications72Support timing for Component - YPbPr input Timing480i480p576i576p720/50p720/60p1080/50i1080/60i1080/24p1080/25p1080/30p1080/50p1080/60

Specifications 73Support timing for Video and S-Video input Support timing for HDMI (HDCP) input Video mode NTSC PAL SECAM PAL-M PAL-N PAL-60 NTSC4.43

Specifications74There timing showing depend the EDID file and VGA graphic card limitation. It is possible that user cannot choose the above timings on

Specifications 75Supporting timing for HDMI Video input Supporting timing for MHL input TimingResolution3D FieldSequential3D framepacking3Dover-under

Warranty and Copyright information76Warranty and Copyright informationLimited warrantyBenQ warrants this product against any defects in material and w

Introduction8• The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/b

Introduction 9Shipping contentsCarefully unpack and verify that you have all of the items shown below. If any of these items are missing, please conta